The contact owns a 2024 Mercedes-Benz CLE450 equipped with Continental Tires, Tire Line: Pro Contact Run Flat SSRMOE, Tire Size: 245/40/R19xl, DOT Number: 16Y0FBK38 PF850. The tires were original equipment. The contact stated that while driving approximately 65 MPH, the front passenger’s side tire had a blowout and tread separation. The vehicle was later towed to the residence of a family member, and a replacement tire of the same make and model was purchased and later mounted to the vehicle. The contact stated that approximately 6,000 miles later, the failure recurred with the replacement tire. The manufacturer and local dealer were notified of the failures, but no assistance was offered. 

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment Outer joint housing before) before coating with Molykote, using spirit (free of dust and grease) 3. Coat contact surface A (see image file in attachment Outer joint housing after) using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).

Complaint USB port not functioning properly. Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: • Fluid intrusion • Broken bushings or physical damage See attachments. Remedy If a component needs replacement but shows no visible external damage, submit a detailed TIPS case only when technical support is required. Include details of all connected external devices (such as charging cables, USB drives, and hard drives). If diagnostic results directly indicate component replacement, a TIPS case is not necessary.

Complaint Harsh 2-1 downshifts when coming to a stop with ECO start-stop function turned OFF. Note: When ECO start-stop is active, the engine is shut off before the 2-1 shift and the complaint will not occur. Cause Software application when engine is running. Remedy Short-term remedy: Perform IPR and follow the instruction to perform standstill adaptations. Long-term Solution: Aftersales software is currently in development. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.

Complaint A harsh 5-4 downshift can be felt during deceleration while braking or coasting. It may be mistaken for a hard brake engagement Cause Poor learning of brake B06 adaptation values over time. Remedy Short-term remedy: 1. Perform IPR and follow the instructions. 2. Perform resetting of deceleration values (VGS > Special Procedures > Special procedure > Resetting learned values Deceleration mode) 3. Perform standard adaptation 4. Reevaluate the concern and release vehicle if no longer present Note: ALL steps (resetting learned values and standard adaptation) must be completed to fully resolve the complaint. Long-term measure: Aftersales software is currently in development.

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause • Wheezing noises: Flow noises of the damper oil • Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced with parts past clean point. • Part clean point is on or after April 2024. • When receiving new parts, check manufacture date (example shown below). • If parts were produced prior to the clean point date, do not install, return. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

Complaint At low speeds and light brake pressure, brakes will make a groaning or honking noise. Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. • Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. • Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: • NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled New onboard electrical system diagnosis shown on BR 166. The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. • Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. • Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. • Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records • NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records • NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: • vehicle technical issue? • customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: • Amperage setting of charger and time battery was on charger • XENTRY Battery Tester results • Voltage of battery taken with multimeter: Do not connect charger while taking measurements • N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) • Workshop analysis of conspicuous data • Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) • NOTE: For expedited results when creating a case write customer complaint as XENTRY Battery Tester implausible. 

Complaint Message in Instrument Cluster for Active Distance Assist not enabled, but can be purchased subsequently even if Digital Extra: Active Distance Assist DISTRONIC (207) has already been activated/purchased via the application. Cause On some vehicles with Digital Extra: Active Distance Assist DISTRONIC (code 207), it may be that the function cannot be enabled via the application or is no longer available in the vehicle back end. Remedy Please open a case with the Customer Care Center (CCC) to reactivate function on the vehicle back end.

Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has updated driver assistance system SCN coding available for certain subject vehicles. The updated SCN coding improves system stability and enhances the availability of driver assistance features.  MBUSA will conduct an OTA service campaign. Remote SCN coding updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Mercedes-Benz CLE450

Filing history

Top reported issues — Mercedes-Benz CLE450

Recent filings